2022 Pharmaceutical Inspection Equipment Upgrade
- Inspection equipment for pill packaging.
- Designed usiing Xilinx FPGA, XC7K160T.
- Incorporates the XC7A15T and XC7A75T used in the previous model.
- Using 16CH ONSemi camera modules and TI DSP Processor.
- Only hardware development and production will proceed.
- The FPGA & DSP algorithm will be implemented by the ordering party.
- Development in progress.
2022 Dust Sensor for Automotive (ASIC Ver.)
- Automotive dust detection sensor for overseas.
- Dust detection class 2.5.
- Using ASIC with built-in dust detection.
- LIN stack and bootloader development.
- ASIC Interface Programming
- Hardware will be design by the ordering party.
- Development in progress.
2022 Dust Sensor for Automotive
- Automotive dust detection sensor for domestic.
- Dust detection class 2.5.
- Dust measurement algorithm and stabilization software programming.
- Optimize analog Interface and respond to mass production.
- Compatible with MISRA-C and LIN standards.
- Hardware will be design by the ordering party.
- Development in progress.
2021 ADC Board for GND Monitoring (Low Performance Version)
- Ground noise tracking and storage of high voltage transmission lines.
- Spark alerts and hazard detection.
- Designed usiing Xilinx FPGA, XC7A100T.
- Downgrades the XC7K325T and ADC10D1000 used in the previous model.
- Trying to reduce the Ground point by replacing 2CH@1GSPS/8CH@200MSPS with 6CH 200MSPS.
- Hardware and FPGA Coding in progress, to be manufactured.
- Development in progress.
2021 LED HEAD/REAR LAMP for Heavy Equipments
- Work lights for heavy equipment such as Excavator and Bulldozers.
- Development for LED Driver Board and LED panel.
- Schematic design, Artwork and PCB Assembly.
- Manufacture was done.
2021 GNSS Interface Board
- GNSS(Global Navigation Satellite System) Module.
- Using MOSAIC-H of SEPTENTRIO.
- One 10/100 Base-T Ethernet port.
- One Micro-USB Type-B, USB 2.0 port.
- Four USART Ports with two TTL ports selectable.
- four User GPIO ports.
- Developed schematic design, PCB Artwork and Assembly.
- Manufacture was done.
2021 Wired Data Measurements GUI
- Non-Public, the ordering party request.
- Monitoring for wired communication (RS232, RS485, RS422).
- For factory automation zero-defect check and security.
- Data Log save & Specific time access.
- Development was done.
2021 UVC LED with White LED for PCR Equipments
- Internal sterilization of PCR test equipment.
- 18 UVC LEDs for sterilization.
- Added two white LED for internal cleaning.
- None LED driver.
- Developed schematic design, PCB Artwork and Assembly.
- Manufacture was done.
2021 ADC Board for GND Monitoring
- Ground noise tracking and storage of high voltage transmission lines.
- Spark alerts and hazard detection.
- Ground Noise data saving and Analysis.
- Designed using Xilinx FPGA, XC7K325T and 2CH@1GSPS/8CH@200MSPS ADCs.
- Included 2GByte DDR3 RAM, two CAN-FD ports, two RS485 ports and Analog Filters.
- Up to 128GByte capacity microflash card available.
- Developed schematic design, FPGA programming, PCB Artwork and Assembly.
- Manufacture was done.
2021 Power Line Monitoring Board
- 16CH power line monitoring and control card.
- Using Xilinx FPGA, Spartan-6.
- Charging current and voltage measurement, cumulative data transmission.
- Hardware and FPGA Coding was done.
- Pre-Production was done.
2021 USART JIG for Production/Test
- Convert USART to CMOS, TTL or 12V.
- Developed for electronic Horn/Buzzer test.
- Available as a USART bootloader jig.
2021 Factory Automation GUI for Electronic Horn/Buzzer
- GUI program for calibration work when producing Horn/Buzzer integrated module.
- Frequency and duty generation and storage using UART communication.
- Development was done.
2021 Electronic Horn/Buzzer Module
- Horn/buzzer integrated module for Automobiles.
- Hardware will be designed by the ordering party.
- Developed Firmware Program only.
- Development was done.
2020 LED Module for Portable Lantern
- LED Board of High Brightness Portable Lantern.
- Developed schematic design and PCB Artwork and Assembly.
- Manufacture was done.
2020 AC/DC Controller for HPC
- High Power Control board on 2KW grade.
- PFC control, output regulation, voltage and current monitoring.
- Built-in OVP, OCV and constant current control function.
- Developed schematic design, PCB Artwork, Firmware programming and Assembly.
- Pre-Production was done.
2020 Communication Board for Ships
- Communication board for ships.
- Four CAN-FD ports.
- Four RS485 ports.
- Two 10/100 Base-T Ethernet ports.
- Developed schematic design, PCB Artwork, Firmware programming and Assembly.
- Manufacture was done.
2020 Wireless Motor Controller for Factory Automation
- Motor controller using SiLAB WiFi module.
- Applied when building a new factory for factory automation.
- RF Extend circuit applied for extended operating range.
- Developed schematic design, PCB Artwork and Assembly.
- Manufacture was done.
2020 Pharmaceutical Inspection Equipment
- Inspection equipment for pill packaging.
- Designed usiing Xilinx FPGA, XC7A15T and XC7A75T two boards.
- Using 16CH ONSemi camera modules and TI DSP Processor.
- Only hardware development and production had proceed.
- The FPGA & DSP algorithm will be implemented by the ordering party.
- Developed schematic design, PCB Artwork and Assembly.
- Manufacture was done
2020 3P4W Multi Watt-Hour Meter
- 3phase 4wire Watt-Hour Meter used in buildings, factories, etc.
- Designed using ST Cortex-M4 MCU and ADI Multiphase Energy, Power Quality Measurement IC.
- Max 16CH Watt-Hour measurement ports.
- One 10/100 Base-T Ethernet port with WiFi.
- One RS232 port and One RS485 port.
- Up to 16GByte capacity micro-flash card available.
- By using the card slot, 4/8/12/16 CH can be switched.
- Developed schematic design, PCB Artwork and Assembly.
- Manufacture was done.
2020 Communication Board for Ships-PCB
- Communication board for ships.
- Two CAN-FD ports.
- Two RS485 ports.
- Two 10/100 Base-T Ethernet ports.
- Developed schematic design and PCB Artwork only.
2020 Valve Driver for Vaccum tube
- Industrial pump on/off controller.
- 7CH Smal signal Relay outputs with 2CH High current Relay outouts.
- 8CH Photo-Coupler outputs.
- One RS232 port.
- In-pipe vacuum measurement.
- Developed schematic design, PCB Artwork, Firmware programming and Assembly.
- Manufacture was done.
2020 MIPI Interface for Medical
- Image data collection and distribution equipment.
- Designed usiing Altera FPGA, 10CX105.
- Only FPGA programming development with IPs.
- Hardware and production will be implemented by the ordering party.
- Development was done.
2019 Portable Airpurifier for Automobiles.
- Airpurifier for Automobiles.
- USB Type-C Power Input.
- Included mood light function with 4-step FAN control.
- No Dust sensor version.
- Buyer to Buyer Project
- Developed schematic design, PCB Artwork, Firmware programming and Assembly.
- Manufacture was done.
2019 Air Cleaner for CES DEMO Board
- Airpurifier for Desk.
- 12V Adaptor Power Input.
- Included mood light function with 5-step FAN control.
- No Dust sensor version.
- CSE2020 entry project.
- Developed schematic design, PCB Artwork, Firmware programming and Assembly.
- Pre-Production was done.
2019 Solar Panel Controller
- 32CH Solar Panel Monitoring Board.
- Interface board re-working for PLC (Power Line Communication) Interface.
- Developed schematic design, PCB Artwork, and Assembly.
- Pre-Production was done.
2019 Wireless 3P4W Watt-Hour Meter
- 3Phase 4Wire Wireless Watt-Hour Meter project.
- Designed usiing ST Cortex-M4 MCU and ADI Multiphase Energy, Power Quality Measurement IC.
- Selectable Bluetooth 5.0, LWRF or AC PLC (Power Line Communication).
- Included pressure and vibration detection function.
- Developed schematic design.
- Development was done.
2019 Image Inerface for LiDAR
- LiDAR sensor data collection and analysis equipment.
- Designed usiing Altera FPGA, 10CX105.
- Only FPGA programming development with IPs.
- Hardware and production will be implemented by the ordering party.
- Development was done.
2018 Electronic Horn Test JIG
- JIG for Horn/Buzzer integrated module test for automobiles.
- Developed schematic design, PCB Artwork, and Assembly.
- Pre-Production was done.